MITSUBISHI
Home >> Products >> MITSUBISHI >> Servo driver/Servo motor >> MR-E series >> HF-SE202JW1-S100 | MITSUBISHI servo motor HF-SE202JW1-S100

HF-SE202JW1-S100 | MITSUBISHI servo motor HF-SE202JW1-S100

MITSUBISHI HF-SE202JW1-S100 Manual And Instructions
HF-SE202JW1-S100 datasheetPDF datasheet

MITSUBISHI HF-SE202JW1-S100 Product information and technical parameters:
Brand: MITSUBISHI
Name: servo motor
Model: HF-SE202JW1-S100
Type: HF-SE servo motor, medium inertia power.
Rated output power: 2.0kw.
Rated speed: 2000r/min.
Electromagnetic brake: No.
Oil seal: have.
Encoder resolution: 131072p/r.
S100 representative: Super MR-E special motor.
KH003 special mark for Super MR-E.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc..
Can improve the performance of equipment.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performance, high precision positioning (servo motor encoder resolution: 131072).
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface.
The analog input interface is used for speed control and torque control.

Type: MR-J series.
Rated output: 0.2KW.
Suitable for motor series: HA-ME.
Voltage: single phase AC100V.
It is very helpful to improve the stability of the low speed control of the servo motor.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control MITSUBISHI HF-SE202JW1-S100 HF-SE202JW1-S100
This can be effectively used in the use of the robot control of the indexing table.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment MITSUBISHI HF-SE202JW1-S100.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor.
Encoder serial communication system, the communication frequency can only be limited to 10M. Motor series: low inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 1.5kw.
Rated speed: 3000rpm.
With the brake: without.
Shaft end: straight shaft.
Performance comparison of servo motor and stepping motor MITSUBISHI HF-SE202JW1-S100.
Stepper motor as an open-loop control system, and modern digital control technology has the essential link.
In the current domestic digital control system, stepping motor is widely used.
With the emergence of digital AC servo system, AC servo motor is more and more used in digital control system.
In order to adapt to the development trend of digital control, most of the motion control system adopts stepping motor or full digital AC servo motor as executive motor.
Although they are similar in control mode (pulse train and directional signal), there are great differences in performance and application.
The use performance of the two are compared.MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 11.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and othher operations HF-SE202JW1-S100.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.

The servo amplifier can be used for speed control operation HF-SE202JW1-S100.
When the two stations are occupied, the speed can be set directly by the remote register.


...More relevant models >>>>