MITSUBISHI
Home >> Products >> MITSUBISHI >> Servo driver/Servo motor >> MR-J4 series >> MR-J4 servo amplifier >> MR-J4-15KA-RJ | MITSUBISHI Servo driver MR-J4-15KA-RJ

MR-J4-15KA-RJ | MITSUBISHI Servo driver MR-J4-15KA-RJ

MITSUBISHI MR-J4-15KA-RJ Manual And Instructions
MR-J4-15KA-RJ datasheetPDF datasheet

MITSUBISHI MR-J4-15KA-RJ Product information and technical parameters:
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J4-15KA-RJ
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 15.0kw.
Interface: General purpose.
Power supply: three phase AC200V.
Special specification: full closed loop control 4 wire / device end encoder ABZ phase input corresponding support function security unit, support positioning mode.
Servo amplifier supporting universal interface.
Servo amplifier for universal interface.
Speed / torque control of position control and analog voltage command can be carried out by using pulse train command.
Support Max instruction pulse frequency 4 Mpulses/s.
The industry''s top level speed motor, the frequency of 2.5kHz amplifier, and optical fiber network extradimensional Symphony orchestra.
Using the traditional two degree of freedom model adaptive control to further optimize the exclusive high speed servo control structure of the dedicated execution engine.
Achieved the fastest 2.5kHz speed frequency response in the industry.
Combined with MITSUBISHI independent research and development of high resolution absolute position encoder (4194304pulses/rev),
Greatly improve the processing speed. Can maximize the performance of high-end machinery.

Type: HA-ME series.
Rated output: 0.4KW.
Rated speed: 3000r/min.
Electromagnetic brake: there.
Control complex, easy to achieve intelligent,
The electronic commutation method is flexible and can be changed by square wave or sine wave.
Motor maintenance free, high efficiency, low operating temperature,
Electromagnetic radiation is very small, long life, can be used in a variety of environments MITSUBISHI MR-J4-15KA-RJ MR-J4-15KA-RJ
AC servo motor is brushless motor, which is divided into synchronous and asynchronous motor,
Synchronous machines are commonly used in motion control,
Its power range, you can do a lot of power.
Large inertia, the maximum rotation speed is low, and with the increase of power and rapid reduction.
So it is suitable for the application of low speed and stable operation MITSUBISHI MR-J4-15KA-RJ.
The rotor of the servo motor is permanent magnet,
Drive controlled U/V/W three phase electric electromagnetic field,
The rotor rotates under the action of the magnetic field,
At the same time the motor comes with the encoder feedback signal to the drive,
According to the feedback value and the target value, the driver is compared,
Adjust the rotor rotation angle MITSUBISHI MR-J4-15KA-RJ.
The accuracy of the servo motor is determined by the accuracy of the encoder. Type: HF-KE servo motor, low inertia, low power.
Rated output power: 0.4kw.
Rated speed: 3000r/min.
Electromagnetic brake: No.
Oil seal: have.
Encoder resolution: 131072p/r.
S100 representative: Super MR-E special motor.
KH003 special mark for Super MR-E.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc..
Can improve the performance of equipment.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performance,, high precision positioning (servo motor encoder resolution: 131072) MR-J4-15KA-RJ.
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface MR-J4-15KA-RJ.
The analog input interface is used for speed control and torque control.


...More relevant models >>>>