MITSUBISHI
Home >> Products >> MITSUBISHI >> Ans/QnAs series PLC >> CPU host >> A171SCPU | MITSUBISHI CPU unit A171SCPU

A171SCPU | MITSUBISHI CPU unit A171SCPU

MITSUBISHI A171SCPU Manual And Instructions
A171SCPU datasheetPDF datasheet
A171SCPU Common InstructionsProgramming Manual
A171SCPU (SV13/22)(REAL MODE)Programming Manual
A171SCPU Dedicated InstructionsProgramming Manual
A171SCPU FundamentalsProgramming Manual
A171SCPU User's Manual

MITSUBISHI A171SCPU Product information and technical parameters:
Brand: MITSUBISHI
Name: CPU unit
Model: A171SCPU

Number of channels: 2 channels.
Sensing method and temperature range: PT100.
A1S64TC series component is a kind of temperature controller combined with ANS series CPU.
Components with temperature measurement input and built-in PID algorithm control output, can be used in a variety of temperature control occasions MITSUBISHI A171SCPU.
Each component controls up to 4 loops at most.
Thermocouple input or PT100 3 wire temperature sensor input A171SCPU
Control output switching signal for the output of the transistor.
BW is a signal with broken line detection function. Input type: AC.
Input points: 16 points.
Input voltage: AC200-240V.
Input current: 11mA.
Connection mode: terminal row.
Common common point: 16.
The instruction list programming language is a programming language similar to assembly language mnemonic,
As well as assembly language by the operation code and the number of operations MITSUBISHI A171SCPU.
In the case of the computer for the PLC handheld programmer compile user program.
At the same time, the programming language of the instruction list corresponds to the ladder diagram programming language,
In PLC programming software can be converted to each other MITSUBISHI A171SCPU. Figure 3 is the instruction sheet corresponding to the ladder diagram of figure 2PLC.
The characteristics of instruction table programming language is used to represent mnemonic operation function,
Easy to remember, easy to grasp;
In the handheld programmer on the keyboard using the mnemonic representation, easy to operate, can be programmed in computer;
There is a one-to-one correspondence between the ladder diagram and the ladder diagram. Its characteristics are basically consistent with the ladder diagram language. 5 slots; requires 1 AnS series PLC power modules;
Used to install large AnS series PLC module.
Base plate of AnS series PLC.
QA1S series PLC 5 slot main substrate.
AnS series of modules can be installed. Input points: 32 points.
Input voltage and current: 7mA DC24V.
Input response time: 10ms.
16 point /1 a public side.
Positive pole sharing.
Output points: 24 points.
Output voltage: DC24V.
OFF leakage current: 0.1mA.
Output response time: 12ms.
Output type: transistor output.
8 point /1 a public side.
With the surge absorber.
34 point terminal station.
PLC is introduced by the relay control technology after the development of micro processing technology,
Can be easily and reliably used for switching control.
As the analog quantity can be converted into digital quantity, the number of digital quantity is just a number of switching value,
Therefore, after the conversion of analog, PLC can also be reliable for processing control.
Because the continuous production process often has the analog quantity, the analog quantity control is sometimes called process control.
Analog quantity is not electricity, and PLC can only handle digital quantity, quantity of electricity.
All to realize the conversion between them to have the sensor, the analog quantity into a number of power.
If this power is not standard, but also through the transmitter,
The non-standard power into a standard electrical signal, such as 1-5V, 4-20mA, 0-10V, etc..
At the same time, there is also an analog input unit (A/D),
Transform these standard electrical signals into digital signals,
The analog output unit (D/A), in order to transform the digital quantity after PLC processing into analog quantity -- standard electric signal A171SCPU.
So the standard telecommunication number, the conversiion between the number of operations to use a variety of computing A171SCPU.
This requires the resolution of the analog unit and the standard electrical signal.


...More relevant models >>>>